176262

Control Arm Kit with stabiliser links and ends

Fitting Position: front axle left, front axle right

176262

Product Information

High wear protection
Robust construction for perfect function
Optimal fitting accuracy for easier repairs
Strict quality standards
Compliance with the requirements of vehicle manufacturers

Vehicle Repairs. We've Got What It Takes.

Rubber-to-metal parts are used as elastic joints between chassis and body, especially in multi-link axle designs. They absorb the vibrations generated by the road surface and drive units while the vehicle is in motion and thus makes a significant contribution to increasing driving comfort and noise insulation. In addition, they ensure driving safety by improving steering behaviour and driving stability on uneven road surfaces as well as braking and avoidance manoeuvers.

The greatest challenge for modern, technologically complex vehicles is the balance between performance, economy, and environmental compatibility. However, many of the roads they drive on are far from perfect. As a result, the chassis and the steering are often subjected to extreme loads, which accordingly increases the quality demands placed on wear parts.

Control arms are the link between the suspension strut and the bodywork. They hold the strut in position and absorb forces in the longitudinal and transverse directions when accelerating and decelerating as well as when cornering. Due to the suspension, they must be mounted so that they can move up and down. Control arms from febi are precisely manufactured and have high-quality supporting ball joints and bearings with the ideal rubber hardness and elasticity.

Steering parts in particular are subject to special care in design, manufacturing, and assembly. This is why febi only offers steering parts in OE matching quality. In order to maintain stable road holding, even in hazardous situations, all installed steering parts must meet the high requirements of precise and high-quality production.

With a large selection of safety-relevant steering components, febi makes a contribution to road safety.

Quality by Conviction

In order to ensure absolutely reliable absorption of the vertical and horizontal forces that occur during acceleration, braking, and cornering, febi's control arm mounting kits are intensively tested.

In the steering technology sector, febi is one of the leading suppliers in the Independent Aftermarket. For example, control arms: the range exclusively includes control arms that guarantee 100% driving stability.

Control arms from febi are therefore intensively tested. Our quality management tests the offered control arms for various requirements and loads, e.g. fitting accuracy, dimensional accuracy, material quality, and tensile strength.

Our quality management tests the products offered for various requirements and loads. These include fitting accuracy, dimensional accuracy, material quality, tensile strength, and degrees of hardness.

In the area of steering technology, febi is one of the leading suppliers in the Independent Aftermarket. The product range exclusively includes control arm mounting kits that guarantee 100% driving stability and meet, or even exceed, the approval requirements.

Supplied Complete. Repaired Non-stop.

In everyday workshop life, it is not uncommon for a wear part to have to be replaced as well as its attachment material. However, these additional articles are often not included with the individually available replacement part.

In everyday workshop life, it is not uncommon for a worn part to have to be replaced as well as any fixings. However, these additional parts - usually bolts or nuts - are often not included with the individually available replacement part.

With the ProKits, febi provides a remedy by offering control arm mounting kits with all attachments required for fair value repair. In addition to control arm bearings, attachment brackets, and ball joints, these kits can also include nuts, bolts, washers, and spring washers.

With the ProKits, febi provides a remedy. febi also offers complete control arm kits for certain vehicle types which contain all the mounting material such as the nuts & bolts required for a professional replacement.

febi ProKit is the tailor-made, complete solution in which necessary repairs can be carried out without delay.

Kit or Set Content

	description	Number	Characteristics
22044	Tie Rod End with nut	2	article version: new implementation Fitting Position: front axle left Fitting Position: front axle right Outside Thread: M14 x 1,5
21904	Control Arm with bush and joint	1	Fitting Position: front axle left Fitting Position: rear Fitting Position: upper Material: aluminium
This article is not sold separately.	Bolt for for stabilizer link	4	Fastening Type: Hexagonal Fitting Position: front axle Length: 71 mm Length under Head: 62 mm Outer Diameter: 21,6 mm Outside Thread: M10 x 1,5 shaft length: 13 mm Tensile Strength Grade: 10.9 Thread Length: 49 mm Wrench Size (metric): 16 mm
22263	Nut	10	collar shape for bolts and nuts: flat seat DIN - ISO: 6927 Fastening Type: Hexagonal Height or Thickness: 11 mm internal thread: M10 x 1,5 Material: steel Outer Diameter: 21,2 mm Surface: galvanized Tensile Strength Grade: 10 Thread Mode: self locking Wrench Size (metric): 16 mm
21481	Bolt for control arm	2	Fitting Position: front axle Length: 106 mm Outside Thread: M10 x 1,5 shaft length: 72 mm Tensile Strength Grade: 8.8 Thread Length: 28 mm Wrench Size (metric): 16 mm
This article is not sold separately.	Bolt	2	Fitting Position: front axle Outside Thread: M10 x 1,5 shaft length: 30 mm Thread Length: 20 mm
This article is not sold separately.	Bolt	2	Fitting Position: front axle Height or Thickness: 2 mm Length: 30 mm Outer Diameter: 22 mm Outside Thread: M8 x 1,25 Thread Length: 21 mm
21906	Control Arm with bush and joint	1	Fitting Position: front axle right Fitting Position: rear Fitting Position: upper Material: aluminium
This article is not sold separately.	Bolt	2	Fitting Position: front axle Length: 120 mm Outside Thread: M12 x 1,5
14392	Hex Nut	4	collar shape for bolts and nuts: flat seat Fastening Type: Hexagonal Height or Thickness: 16 mm internal thread: M12 x 1,5 Tensile Strength Grade: 10 Thread Mode: self locking Wrench Size (metric): 18 mm
21920	Stabilizer Link	1	Fitting Position: front axle left height: 32 mm Height or Thickness: 38 mm hole pitch: 90 mm internal thread: M10 x 1,5 Length: 125 mm Material: aluminium Wrench Size (metric): 13 mm
This article is not sold separately.	Collared Bolt for for stabilizer link	4	Length: 59,5 mm Outer Diameter: 22 mm Outside Thread: M10 x 1,5 shaft length: 23 mm Tensile Strength Grade: 10.9 Thread Length: 27 mm Wrench Size (metric): 16 mm
21922	Stabilizer Link	1	Fitting Position: front axle right height: 32 mm Height or Thickness: 38 mm hole pitch: 90 mm internal thread: M10 x 1,5 Length: 125 mm Material: aluminium Wrench Size (metric): 13 mm
21928	Control Arm with bushes and joint	2	Fitting Position: front Fitting Position: front axle left Fitting Position: front axle right Fitting Position: lower Material: aluminium
This article is not sold separately.	Bolt	2	Fitting Position: front axle Length: 108 mm Length under Head: 92 mm Outer Diameter: 24 mm Outside Thread: M12 x 1,5 Tensile Strength Grade: 10.9 Wrench Size (metric): 18 mm
This article is not sold separately.	Nut with captive disc	2	Fastening Type: Hexagonal Height or Thickness: 15 mm Outer Diameter: 35 mm Outside Thread: M12 x 1,5 Tensile Strength Grade: 8 Wrench Size (metric): 18 mm
This article is not sold separately.	Nut for control arm	2	Fastening Type: Hexagonal Height or Thickness: 11 mm internal thread: M10 x 1,5 Outer Diameter: 20 mm Tensile Strength Grade: 10 Wrench Size (metric): 16 mm
This article is not sold separately.	Hex Bolt	2	Fastening Type: Hexagonal Length: 82 mm Outside Thread: M12 x 1,5 shaft length: 45 mm Tensile Strength Grade: 10.9 Thread Length: 30 mm Wrench Size (metric): 18 mm
11137	Control Arm with bush and joint	1	article version: new implementation Fitting Position: front Fitting Position: front axle left Fitting Position: upper Material: aluminium
11138	Control Arm with bush and joint	1	article version: new implementation Fitting Position: front Fitting Position: front axle right Fitting Position: upper Material: aluminium
11352	Control Arm with bush and joint	1	article version: old implementation Fitting Position: front axle left Fitting Position: lower Fitting Position: rear Material: aluminium Outer Diameter: 29 mm
11351	Control Arm with bush and joint	1	article version: old implementation Fitting Position: front axle right Fitting Position: lower Fitting Position: rear Material: aluminium

Technical information

Selected Language / Multilanguage

Alternate Language

febiINFO English

Comparison Number(s)

Suitable to replace	Reference(s)
Audi	8E0 407 151 R S4 \| 8E0 407 151 E S4 \| 8E0 407 151 K S4 \| 8E0 407 151 L S4 \| 8E0 407 151 M S4 \| 8E0 407 151 N S4
Seat	8E0 407 151 R S4 \| 8E0 407 151 E S4 \| 8E0 407 151 K S4 \| 8E0 407 151 L S4 \| 8E0 407 151 M S4 \| 8E0 407 151 N S4

Used In Vehicles

These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Trouble finding the part you were looking for?

Inform us here!

Please let us know the OE reference number for the part you cannot find. Alternatively, please include the vehicle registration or VIN with a description of the product you require. All feedback will be considered in our range development process for new bilstein group articles.

E-Mail

Country

Please provide the details below:

By submitting this form you accept our Data Protection Regulations .

Have a general inquiry?

If you have a sales, technical or warranty query - or something else entirely - please follow the link below:

Contact

FANS is a tool that allows you, as a user of partsfinder, to contribute to the ongoing development of the bilstein group product range to ensure we have the right articles - for the right applications - at the right time.