14414

Mounting Kit for control arm

Fitting Position: front axle left, front axle right

14414

Attributes
Additional Information / Parts	Additional Information / Parts: with coupling rod
Additional Information / Parts	Additional Information / Parts: without support/ steering link
Article Version	Article Version: new implementation

Product Information

High wear protection
Optimal fitting accuracy for easier repairs
Strict quality standards
Compliance with the requirements of vehicle manufacturers

Vehicle Repairs. We've Got What It Takes.

The greatest challenge for modern, technologically complex vehicles is the balance between performance, economy, and environmental compatibility. However, many of the roads they drive on are far from perfect. As a result, the chassis and the steering are often subjected to extreme loads, which accordingly increases the quality demands placed on wear parts.

Steering parts in particular are subject to special care in design, manufacturing, and assembly. This is why febi only offers steering parts in OE matching quality. In order to maintain stable road holding, even in hazardous situations, all installed steering parts must meet the high requirements of precise and high-quality production.

With a large selection of safety-relevant steering components, febi makes a contribution to road safety.

Quality by Conviction

In order to ensure absolutely reliable absorption of the vertical and horizontal forces that occur during acceleration, braking, and cornering, febi's control arm mounting kits are intensively tested.

Our quality management tests the products offered for various requirements and loads. These include fitting accuracy, dimensional accuracy, material quality, tensile strength, and degrees of hardness.

In the area of steering technology, febi is one of the leading suppliers in the Independent Aftermarket. The product range exclusively includes control arm mounting kits that guarantee 100% driving stability and meet, or even exceed, the approval requirements.

Supplied Complete. Repaired Non-stop.

In everyday workshop life, it is not uncommon for a worn part to have to be replaced as well as any fixings. However, these additional parts - usually bolts or nuts - are often not included with the individually available replacement part.

With the ProKits, febi provides a remedy and offers control arm mounting kits with all attachments required for fair value repair. In addition to control arm bearings, attachment brackets, and ball joints, these can also include nuts, bolts, washers, and spring washers.

Kit or Set Content

	Description	Quantity	Attributes
07856	Control Arm Bush	1	Fitting Position: front Fitting Position: front axle left Fitting Position: front axle right Height or Thickness: 54 mm Inner Diameter: 12 mm Material: rubber / metal Outer Diameter: 33 mm Outer Diameter: 36 mm
07847	Control Arm Bush	1	Article Version: new implementation Fitting Position: front axle left Fitting Position: front axle right Fitting Position: lower Fitting Position: rear Height or Thickness: 41 mm Inner Diameter: 17 mm Material: Aluminium Material: rubber / metal Outer Diameter: 27 mm Outer Diameter: 60 mm
07863	Stabiliser Link with rubber mounts	1	Additional Information / Parts: with nut Fitting Position: front axle left Fitting Position: front axle right Material: metal Outside Thread: M8 x 1,25 Thread Length: 14 mm Wrench Size (Metric): 13 mm
This article is not sold separately.	Lock Washer for ball joint	1	Internal Thread: M8 x 1,25
This article is not sold separately.	Bolt for ball joint	3	Length: 34 mm Length under Head: 26 mm Outer Diameter: 16,5 mm Outside Thread: M8 x 1,25 Surface: oiled Tensile Strength Grade: 10.9 Wrench Size (Metric): 13 mm
This article is not sold separately.	Bolt for ball joint	1	DIN - ISO: 8765 DIN - ISO: 960 Length under Head: 80 mm Outside Thread: M12 x 1,5 Surface: galvanized Tensile Strength Grade: 8.8 Thread Length: 30 mm
03544	Sleeve for control arm bush	1	Fitting Position: front axle Height or Thickness: 0,5 mm Inner Diameter: 16 mm Length: 50 mm Outer Diameter: 17 mm

Available in Kit or Set

07858

Control Arm

with additional parts and joint

07859

Control Arm

with additional parts, without joint

03546

Control Arm

with additional parts and joint

14416

Mounting Kit

for control arm

Customers also bought

24372

Bolt Kit

for control arm

24374

Bolt Kit

for control arm, with locking bolt

Comparison Number(s)

Suitable to replace	Reference(s)
Seat	191 407 153 S2
Volkswagen (VW)	191 407 153 S2

Used In Vehicles

These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Trouble finding the part you were looking for?

Inform us here!

Please let us know the OE reference number for the part you cannot find. Alternatively, please include the vehicle registration or VIN with a description of the product you require. All feedback will be considered in our range development process for new bilstein group articles.

E-Mail

Country

Please provide the details below:

By submitting this form you accept our Data Protection Regulations .

Have a general inquiry?

If you have a sales, technical or warranty query - or something else entirely - please follow the link below:

Contact

FANS is a tool that allows you, as a user of partsfinder, to contribute to the ongoing development of the bilstein group product range to ensure we have the right articles - for the right applications - at the right time.